Wear 0.006g｜High Wear Resistance for Industrial Floors

Wear: Only 0.006g – Low wear ensures the floor withstands forklifts and foot traffic over time.
Summary: Factory floors endure constant friction and heavy loads from foot traffic, carts, and forklifts, leading to premature wear, color loss, and exposure of the base layer. CS-2000 Floor Colorant passed aging tests at the Guangzhou Aging Institute. Under a 50g load with 500 revolutions using a CS-10 grinding wheel, the abrasion loss was only 0.006g. Its superior wear resistance significantly extends the lifespan of colored flooring.
Floor wear is an unavoidable pain point in industrial projects.
Industrial plants, logistics warehouses, and underground parking garages endure daily wear from foot traffic, frequent cart movement, and repeated forklift operation.
Excessive wear on the colored floor surface can lead to a series of issues:
The top layer gradually wears thin, causing the color to fade. This results in exposed substrate and uneven appearance, leading to significant color differences between old and new areas.
👉 After wear, the paint film thins and protection decreases, allowing moisture and oil to penetrate the substrate.
Severe wear requires full refurbishment, halting production and incurring high maintenance costs.
Many people confuse wear resistance with scratch resistance:
Scratch resistance is the ability to withstand scratches from sharp objects. Abrasion resistance measures the weight loss of the coating after continuous friction. A lower abrasion value indicates less material wear, resulting in a more durable floor.
Industry Benchmark for Abrasion Resistance & Competitor Comparison
Test standard: GB/T 1768‑2006. Test setup: CS‑10 grinding wheel, 500g weight, 500 rotations. Abrasion resistance is evaluated by mass loss (g); lower values indicate better durability.
0.020g: Standard colored epoxy topcoat with high wear; suitable only for low-traffic areas. Frequent forklift traffic will cause rapid wear and expose the base layer in a short time.
0.010‑0.020g: Modified epoxy and standard floor coloring products suitable for light-duty workshops; not recommended for areas with frequent forklift traffic.
≤0.010g: Mid-to-high wear-resistance tier (CS-2000 tests show 0.006g falls within this range); withstands normal foot traffic, carts, and forklift loads; ideal for industrial facilities.
≤0.003g: Ultra-wear-resistant polyurea and special polyurethane, typically used for heavy-duty extreme conditions; higher product cost.
Competitive Comparison: Most standard epoxy colored paints and floor coloring products on the market have wear values ranging from 0.012 to 0.025g. CS-2000, however, shows a wear value of only 0.006g, with significantly lower weight loss than typical colored floor coatings. Its abrasion resistance is superior.
In simple terms: Under the same friction conditions, the CS-2000 coating loses less material. It is less likely to wear through or fade from prolonged traffic, keeping the colored finish intact for longer.
CS-2000 Floor Coating | Abrasion Resistance Test
CS-2000 flooring stain samples were sent to the Chemical Industry Synthetic Materials Aging Quality Supervision and Testing Center (Guangzhou Aging Institute) for comprehensive paint film performance testing.
Test Item: Abrasion Resistance (CS-10, 500g, 500r)
Test Results: Wear 0.006g
⚠️ Note: Test results apply only to the submitted sample. Accelerated wear testing is conducted in the lab; actual service life also depends on site load, usage frequency, and base conditions.
Practical value for project implementation
Industrial Facilities: Withstands frequent forklift and hydraulic pallet truck traffic to slow surface wear and prevent fading or bare spots.
▪ Logistics & Warehousing: High-traffic cargo handling and cart movement require durable, color-maintained flooring.
▪ Underground parking: Withstands long-term tire friction, extending the lifespan of floor finishes.
High-traffic public spaces: With high-density foot traffic, reduces the frequency of renovations and maintenance.
Note: CS-2000 is a single-component floor coloring agent. Please follow the recommended construction process for application. Additional performance properties such as scratch resistance, heat resistance, boiling water resistance, and chemical resistance are covered in separate test reports, which can be provided upon request.
Final Thoughts
The durability of the base floor determines how long the colored surface layer lasts.
Aesthetic appeal is just the starting point for floor coatings. Long-term durability—resisting wear and fading—is the true necessity for industrial flooring. CS-2000 Floor Stainers undergo independent third-party testing, offering 0.006g low abrasion to deliver durable, colored flooring solutions for high-wear environments like factories and warehouses.
For the full test report, please contact your business representative.